Best Door Tools Store

24″ x 24″ Drywall Inlay Access Panel for masonry applications BA-MW – Aluminum frame, with drywall inlay, for masonry applications The access panel consists of a welded aluminum frame and is available with or without drywall inlay of 1 2″ (12.7 mm) or 5 8″ (15.9 mm) and two latches (comes standard with inlay and touch latches). Both an outer and an inner frame assembly consists of high grade aluminum which is bonded with a special welding process for sizes 12″ x 12″ (305 mm x 305 mm) and up the access panels are equipped with a safety system to prevent accidental opening. This safety system must be reattached if the hatch is removed. The reveal of 1 6 of an inch (1.59 mm) is visible between the outer frame and door hatch. The concealed snap locks open the access panel when pressure is applied to the spring loaded latch side. This access panel is designed to be recessed into concrete wall systems. This panel comes with predrilled holes for easy installation. http: www.bestaccessdoors.com content BA-MW.pdf (BA-MW) Special advantagesSuperior engineering innovative designFast deliveryQuick and easy installationSolid aluminum frameFlush installation in ceilings and wallsAvailable in moisture resistant, mildew resistant and cement board Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

8″ x 8″ Drywall Inlay Access Panel for Exterior Facade BA-MPL – Access panel for stucco The access panel consists of aluminum profiles, a sheet steel insert with expanded metal and a round cylinder lock with key. Both, an outer and an inner frame of the access panel consist of four single frames, which are firmly connected due to a special welding process. The access panel is equipped with a safety-system against accidental opening. In order to avoid accidents, this safety-system has to be secured after each opening. A joint gap of 3 mm is visible between outer frame and door leaf, which is equipped with an innovative brush joint (air-tight and dust-proof) and, in addition, with a special joint (water resistant). Access panels for facades in the outer area are applicable for direct mounting onto solid walls (without external wall insulation system) or for installation into a wall insultion system (foam-sealed) from an insulation thickness of 80 mm http: www.bestaccessdoors.com (BA-MPL) Special advantagesEconomical solutionDelivery at short notice on requestEasy and quick installationSolid aluminum frameSophisticated solutionFlush installation in facades Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

12″ x 12″ Drywall Inlay Access Panel for masonry applications BA-MW – Aluminum frame, with drywall inlay, for masonry applications The access panel consists of a welded aluminum frame and is available with or without drywall inlay of 1 2″ (12.7 mm) or 5 8″ (15.9 mm) and two latches (comes standard with inlay and touch latches). Both an outer and an inner frame assembly consists of high grade aluminum which is bonded with a special welding process for sizes 12″ x 12″ (305 mm x 305 mm) and up the access panels are equipped with a safety system to prevent accidental opening. This safety system must be reattached if the hatch is removed. The reveal of 1 6 of an inch (1.59 mm) is visible between the outer frame and door hatch. The concealed snap locks open the access panel when pressure is applied to the spring loaded latch side. This access panel is designed to be recessed into concrete wall systems. This panel comes with predrilled holes for easy installation. http: www.bestaccessdoors.com content BA-MW.pdf (BA-MW) Special advantagesSuperior engineering innovative designFast deliveryQuick and easy installationSolid aluminum frameFlush installation in ceilings and wallsAvailable in moisture resistant, mildew resistant and cement board Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

16″ x 16″ Drywall Inlay Access Panel for masonry applications BA-MW – Aluminum frame, with drywall inlay, for masonry applications The access panel consists of a welded aluminum frame and is available with or without drywall inlay of 1 2″ (12.7 mm) or 5 8″ (15.9 mm) and two latches (comes standard with inlay and touch latches). Both an outer and an inner frame assembly consists of high grade aluminum which is bonded with a special welding process for sizes 12″ x 12″ (305 mm x 305 mm) and up the access panels are equipped with a safety system to prevent accidental opening. This safety system must be reattached if the hatch is removed. The reveal of 1 6 of an inch (1.59 mm) is visible between the outer frame and door hatch. The concealed snap locks open the access panel when pressure is applied to the spring loaded latch side. This access panel is designed to be recessed into concrete wall systems. This panel comes with predrilled holes for easy installation. http: www.bestaccessdoors.com content BA-MW.pdf (BA-MW) Special advantagesSuperior engineering innovative designFast deliveryQuick and easy installationSolid aluminum frameFlush installation in ceilings and wallsAvailable in moisture resistant, mildew resistant and cement board Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

18″ x 18″ Drywall Inlay Access Panel for masonry applications BA-MW – Aluminum frame, with drywall inlay, for masonry applications The access panel consists of a welded aluminum frame and is available with or without drywall inlay of 1 2″ (12.7 mm) or 5 8″ (15.9 mm) and two latches (comes standard with inlay and touch latches). Both an outer and an inner frame assembly consists of high grade aluminum which is bonded with a special welding process for sizes 12″ x 12″ (305 mm x 305 mm) and up the access panels are equipped with a safety system to prevent accidental opening. This safety system must be reattached if the hatch is removed. The reveal of 1 6 of an inch (1.59 mm) is visible between the outer frame and door hatch. The concealed snap locks open the access panel when pressure is applied to the spring loaded latch side. This access panel is designed to be recessed into concrete wall systems. This panel comes with predrilled holes for easy installation. http: www.bestaccessdoors.com content BA-MW.pdf (BA-MW) Special advantagesSuperior engineering innovative designFast deliveryQuick and easy installationSolid aluminum frameFlush installation in ceilings and wallsAvailable in moisture resistant, mildew resistant and cement board Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

20″ x 20″ Drywall Inlay Access Panel for masonry applications BA-MW – Aluminum frame, with drywall inlay, for masonry applications The access panel consists of a welded aluminum frame and is available with or without drywall inlay of 1 2″ (12.7 mm) or 5 8″ (15.9 mm) and two latches (comes standard with inlay and touch latches). Both an outer and an inner frame assembly consists of high grade aluminum which is bonded with a special welding process for sizes 12″ x 12″ (305 mm x 305 mm) and up the access panels are equipped with a safety system to prevent accidental opening. This safety system must be reattached if the hatch is removed. The reveal of 1 6 of an inch (1.59 mm) is visible between the outer frame and door hatch. The concealed snap locks open the access panel when pressure is applied to the spring loaded latch side. This access panel is designed to be recessed into concrete wall systems. This panel comes with predrilled holes for easy installation. http: www.bestaccessdoors.com content BA-MW.pdf (BA-MW) Special advantagesSuperior engineering innovative designFast deliveryQuick and easy installationSolid aluminum frameFlush installation in ceilings and wallsAvailable in moisture resistant, mildew resistant and cement board Customized solutions Customized sizes can be produced in every dimension upon request. http: www.bestaccessdoors.com custom-size-access-doors (Request a Quote).

18″ x 18″ Recessed Access Door for Drywall “no studs required” – Bauco Designed to provide access in walls and ceilings, while maintaining an invisible, architecturally pleasing appearance. The door panel is supplied with one layer of 5/8″ drywall (or 1/2″). The concealed hinge and removable door panel, along with the easy installation and finishing process, make this access door the best drywall access door in the industry. – Application: – Designed to provide access in walls and ceilings, while maintaining an invisible, architecturally pleasing appearance Product Features Product Features – Designed to accomodate 5/8″ drywall, the frame can be reversed to accomodate 1/2″ drywall- Standard with a touch latch feature BA-BP-58 Access Door Specifications: – Door: Aluminum extrusion with 5/8″ drywall inserted into door panel- Door Frame: Recessed aluminum extrusion provides similar edge to drywall bead against which wall or ceiling surface can be finished- Hinge: Unique concealed non corroding two point pin hinge- Standard Latch: Screwdriver operated cam latch- Finish: Mill Finish. Drywall is ready to be finished to match surrounding wall or ceiling surface.

12″ x 12″ Press-Fit Drywall Access Panel The Press-Fit door is a unique lightweight door that installs easily by bending the tabs on the return back to grip the drywall. The frame, return and doorstop are one-piece construction with a beveled frame resulting in an attractive finished look. BA-PF Press Fit Door Specifications Door: 12″ wide x 12″ high Rough Opening Size: 11 13/16″ wide x 11 13/16″ high Material: 22 gauge cold rolled steel Lock/Latch: Flush to surface, screwdriver operated cam latch Flange: 1½” beveled flange Hinge: Concealed, continuous piano hinge Finish: Prime coat of rust inhibitive electrostatic powder, baked grey enamel.

14″ x 14″ Press-Fit Drywall Access Panel The Press-Fit door is a unique lightweight door that installs easily by bending the tabs on the return back to grip the drywall. The frame, return and doorstop are one-piece construction with a beveled frame resulting in an attractive finished look. BA-PF Press Fit Door Specifications Door: 14″ wide x 14″ high Rough Opening Size: 13 13/16″ wide x 13 13/16″ high Material: 22 gauge cold rolled steel Lock/Latch: Flush to surface, screwdriver operated cam latch Flange: 1½” beveled flange Hinge: Concealed, continuous piano hinge Finish: Prime coat of rust inhibitive electrostatic powder, baked grey enamel.

18″ x 18″ Press-Fit Drywall Access Panel The Press-Fit door is a unique lightweight door that installs easily by bending the tabs on the return back to grip the drywall. The frame, return and doorstop are one-piece construction with a beveled frame resulting in an attractive finished look. BA-PF Press Fit Door Specifications Door: 18″ wide x 18″ high Rough Opening Size: 17 13/16″ wide x 17 13/16″ high Material: 22 gauge cold rolled steel Lock/Latch: Flush to surface, screwdriver operated cam latch Flange: 1½” beveled flange Hinge: Concealed, continuous piano hinge Finish: Prime coat of rust inhibitive electrostatic powder, baked grey enamel.