Best Door Tools Store

Pictured Assembled
Drum, Spacers, Cutters, and Shaft Sold Individually

EDCO Scarifier Accessories

• CPM-8 6 Shaft Drum
• CPM-10 6 Shaft Drum
• CPM-10 8 Shaft Drum
• CPU-10FC 4 Shaft Drum
• CPU-10FC 6 Shaft Drum
• CPM-10 (6 Shaft) Shaft
• CPM-10 (8 Shaft) Shaft
• CPU10FC 11-3/8″ Shaft for use on 10″ Drum
• CPU12 13-5/8″ Shaft for use on 12″ Drum
• Bushing 3/4″ inside diameter
• Steel Spacer
• Spacer 1-1/2″ OD x 3/4″ ID

For use with Edco Scarifier

.

Drum Not Included With Startup Pack

Edco	Kit Description
CPM-8 Pak 1	78 CP206-T Cutters 215 Spacers, 6 Shafts
CPM-8 Pak 2	150 JRS501 Cutters 175 Spacers, 6 Shafts
CPM-8 Fine Setup	96 CP206-T Cutters 174 Spacers, 6 Shafts
CPM-10 6 Shaft Pak	102 CP308-T Cutters 252 Spacers, 6 Shafts
CPM-10 8 Shaft Pak	152 CP206-T Cutters 384 Spacers, 8 Shafts
CPU10FC 6 Shaft Pak	96 CP308-T Cutters 240 Spacers, 6 Shafts, 12 Bushings
CPU10FC 4 Shaft Pak	64 CP408-TV 130 Spacers, 4 Shafts, 8 Bushings
CPU-12 Pak	100 CP408-TV 300 Spacers, 6 Shafts, 12 Bushings

.

Edco Scabblers

Scabblers use compressed air to hammer piston-mounted bits into the concrete surface roughening the concrete surface more than grinding or scarifying. EDCO’s Chip-Dek Scabbler can remove up to 1/4 inch of concrete surface in a single pass. The actual production rate depends on the strength of the concrete. A typical removal rate for a machine with a 12-inch working width is 200 to 250 square feet per hour at a 1/8-inch depth.

Edco	CD-3	CD-5
Power	Air	Air
Air Power	100 CFM at 100PSI	160 CFM at 100PSI
Phase	NA	NA
RPM’s	NA	NA
Belts	NA	NA
Length	41.5″	44″
Width	21″	29″
Weight	165 lbs	278 lbs

Edco CD-3 3-Head Scabbler

Production Rate:

• Remove up to 200 sq ft per hour at depth per pass of 3/16″
• 3 Scabbler heads provide 8″ working width

Production Notes:

• Provides 1200 hits per minute for fast surface removal
• 2″ Vacuum Port for dust-free operation
• Equipped with an in-line lubricator
• Equipped with a Whip-check safety cable, assures safe air hose hookup
• Heavy-duty 1/4″ steel frame

Ideal For:

• Creating slip-resistant surfaces
• Creating wheelchair access ramps
• Creating excellent bonding texture for overlays
• Sidewalk trip hazard repair
• Removing delaminated concrete surface materials
• Removing spalled or deteriorated concrete
• Reducing high spots or leveling uneven joints
• Texturing parking garage ramps

Edco CD-5 5-Head Scabbler

Production Rate:

• 5 Scabbler heads provide 11-1/2″ working width
• Remove up to 250 sq ft per hour at depth per pass of 1/4″

Production Notes:

• Provides 1200 hits per minute for fast surface removal
• Equipped with a Whip-check safety cable, assures safe air hose hookup
• Requires only 160 CFM at 100 PSI
• Heavy-duty 1/4″ steel frame
• Wide T-Grip Handle and 8″ wheels for superior balance and handling
• 3″ Vacuum Port for dust-free operation
• Automatic in-line oiler

Ideal For:

• Creating slip resistant surfaces
• Scabbling down high spots or leveling uneven joints
• Roughening surfaces for new overlayments
• Creating wheelchair access ramps
• Creating excellent bonding texture for overlays
• Removing delaminated concrete surface materials
• Removing epoxy
• Texturing parking garage ramps
• Removing spalled or deteriorated concrete
• Breaking up ceramic tile

.

Edco Scabbler Accessories

• 5 Point and 9 Point Bits are made from Tungsten Carbide
• Bit removal slide hammer will assist you in removing your old bits from either Scabbler

5-Point Bit

• The 5-Point Bit penetrates the surface up to 1/4″ per pass and leaves a rough texture.
• Ideal for:
• Breaking up blistered or spalling concrete
• Removing floor coatings
• Roughening the surface to create a bond for repairs or overlays
• General Surface Removal

9-Point Bit

• The 9-Point Bit penetrates the surface up to 1/8″ per pass and leaves a medium texture.
• Ideal for:
• Creating excellent bonding texture for thin overlays of polymer concrete, epoxy or urethane
• Leveling uneven joints
• Surface removal for repairing spalled and deteriorated slabs

.

Edco	Cutter Description
CP308-T	8 Point, Tungsten Carbide 2 1/4″ OD x 3/4″ ID x 1/4″ Thick
CP404-P6	15 Point Pointed, Steel 2 3/8″ OD x 3/4″ ID x 3/16″ Thick
CP404	10 Point Flat Tip,Steel 2 3/8″ OD x 1″ ID x 3/16″ Thick

.

Edco	Cutter Description
CP408-TV	8 Point, Tungsten Carbide 3 1/8″ OD x 1 3/16″ ID x 5/16″ Thick
CP405-P	15 Point Pointed, Steel 3″ OD x 1″ ID x 3/16″ Thick
CP405	15 Point Flat Tip,Steel 3″ OD x 1″ ID x 3/16″ Thick

.

Edco 8″ Walk Behind Push Scarifier

The CPM-8 is the perfect machine for sidewalk repair, coatings and traffic line removal, creating non-slip surfaces and much more!

Features:

Up to 8″ working width (20 cm.)

Up to 1/8″ working depth per pass (3 mm.)

Power source over drum to eliminate vibration and maximize surface contact Compact design

Front-mounted lifting handle makes loading and unloading easy

Vacuum port equipped

Water misting system standard

Length 35″, width 20″, Height 39″.

Electric model 230 Volts Single Phase, or Three Phase 230/460 Volts.

Down cut drum rotation

Optional edger attachment allows the CPM-8 to get within 1-3/4″ of any vertical surface.

Ideal For:

• Sidewalk trip hazard repair
• Concrete and Coatings removal
• Floor cleaning and/or preparation
• Traffic line and markings removal
• Creating non-slip surfaces
• Includes Drum and six Shafts

.

Edco CPM10 10in Push Scarifier

The new push model CPM-10 features a side loading large drum assembly and a 10″ wide cut which removes 3/16″ per pass.

• Side loading large drum assembly
• 10” wide cut which removes 3/16” per pass
• Heavy-duty 1/4” steel frame with over sized bearings
• Weighs 299 lbs. with cutters
• Teathered emergency stop switch
• Larger 6” wheels in the rear for easy handling
• Gasoline or Electric models available
• Vacuum port standard for dust-free cutting
• Tungsten carbide or steel cutters available
• Electric model 7.5 hp, 3 Phase 230 or 460 Volts.
• 13 HP Honda gas motor
• 6 shaft and 8 shaft easy change, side loading drums available.
• Dimensions: Length 41″, width 23″, Height 41″.

Ideal For:

• Aggressive removal of material
• Production scarification
• Heavy coatings removal
• Repair trip hazards or warehouse fork truck bumps

.

Edco CPU10 10in Self-Propelled Scarifier

The CPU-10(FC) is ideal for larger jobs on concrete or asphalt such as parking deck repairs, factory floor preparation or road repairs

Features:

• Up to 10″ working width (25 cm.)
• Adjustable depth control up to 3/16″ working depth per pass (5 mm.)
• Up-cut drum rotation and heavyweight construction increases production and lifts even the toughest floor coatings
• Hydrostatic transmission with forward and reverse drive provides smooth speed changes and less operator fatigue
• Includes lifting bail, oil alert and hour meter Optional outrigger axle enables the CPU-10(FC) to follow slab contours closely when working on uneven surfaces
• Length 49″, Width 24″.
• Electric 3 Phase, 230 Volts or 460 Volts.

Ideal For:

• Parking deck and road repairs
• Factory floor cleaning and/or preparation
• Road repair
• Mall floor repairs

Performance:

• 500-750 sq. ft./hr – (46-70 sq. m./hr) at a depth of 1/8″ (3 mm.)

Specialty Set-Ups

• Convertible hood design on CPU-10FC model allows for multiple drum set-ups and provides easy access for quick drum changes

.

Edco 12″ Self-Propelled Scarifier

With a working width to 12″, the CPU-12 is for high production use in industrial plants, malls, dairy barns, roads or warehouses.

Features

• Up to 12″ working width (30 cm.)
• 1,250-1,500 sq. ft./hr – (116-139 sq. m./hr) at a depth of 1/8″ (3 mm.)
• Adjustable to 1/4″ working depth per pass (6 mm.)
• Accommodates EDCO’s largest cutters for longer life and more removal
• Electric 3 Phase 230/460 Volts.
• 38 HP Gasoline Wisconsin

Ideal For:

• Planing concrete, asphalt and epoxies elastomerics and masterplate floors with ease
• High production use in industrial plants, malls, dairy barns, warehouses and on roads

Product Notes:

• Up-cut drum rotation and heavyweight construction provide faster milling action and more uniform surface texture
• Hydraulic-powered engage/disengage lever lowers or raises drum from surface
• Standard Outrigger Axle Assembly enables the machine to follow slab contours closely when working on uneven surfaces and provide uniform surface removal
• Hydrostatic drive transmission provides a smooth forward & reverse speed control and less operator fatigue
• Cam-operated fifth wheel allows the operator to change direction or reposition the machine while the engine is still running
• Dimensions: Length 53″, Width 36″, 43″ Height.

Optional:

• A propane kit is available for the CPU-12

.