Category: Edco
7973 Edco Strip Serts by
Edco Strip-Serts
Strip-Serts are carbide tipped blocks designed to clean floors without grinding into the concrete
- The multi-sided, replaceable tungsten carbides have four edges that can be rotated for maximum use.
- The carbide Strip-Serts will clean your surface without any damage.
- Best for removing mastics, paint build-ups, resins, tar, fiberglass, ice and industrial build-ups.
- Screws & Allen wrench & washers included in Kit.
.
7974 Edco Wire Brush Grinder Accessories by Edco
- Hard steel strips mounted in wooden blocks
- Ideal for removing grease deposits, wax or food products and for breaking up rubber backed carpeting
.
7906 Edco 8 hp Gasoline Air Compressor by Edco
Edco 8 hp PAC-8 Air Compressor
8 HP 16.2 CFM @ 100 PSI Air Compressor with Low Oil Shutdown
- Heavy-Duty two stage pump with cast iron cylinder, cast aluminum head and 62 oz. crankcase pre-filled with oil
- Heavy-Duty 2 piece, 16 gauge bolted belt guard
- Pilot valve unloading system with aluminum manifold
- Metal intake filter/silencer with replaceable element
- Automatic engine idle for economy and long service life
- Extra heavy-duty tank assembly with 9 gallon capacity
- Oil drain extensions on pump and engine
- Fully pneumatic/steel hub wheels
- 7 gauge steel construction
- Stainless steel reed valves
- Schmidt belt tightening device
- Flexible braided discharge line
- Automotive style bearing inserts
| Edco | Air Compressor |
Power |
| Horse Power | Honda |
| Belts | |
| Length | |
| Width | |
| Height | |
| Weight |
- Product Notes:
- Cast aluminum head & 62 oz crankcase pre-filled with oil
- Exclusive floating beam design prevents cracking
- Copper discharge line and oil level sight glass
- 2 Edco ALR Chisel Scalers
- 1 Edco Big Stick Chisel Scaler
- 6-8 framing/sheathing guns or 8-10 roofing guns
Ideal For:
.
7901 Edco 250 CFM Vacuum by
Edco 250 CFM Vacuum
| Edco | Power |
| Horse Power | 1.3 hp Motors |
| Phase | |
| Amps | |
| Length | |
| Width | |
| Height | |
| Weight |
- Ideal For:
- Edco Floor Grinders & Turbo Grinders
- Edco Crack Chaser
- Edco Traffic Line Remover
- Edco 10″ Scarifiers
.
7902 Edco 500 CFM Vacuum by
Edco 500 CFM Vacuum
| Edco | Power |
| Horse Power | 230 V |
| Phase | |
| Amps | |
| Length | |
| Width | |
| Height | |
| Weight |
- Ideal For:
- Edco 12″ Scarifiers
- Edco Masonry Saws
- Multiple Edco machines
.
7898 Edco Scarifier Accessories by
Pictured Assembled
Drum, Spacers, Cutters, and Shaft Sold Individually
EDCO Scarifier Accessories
- CPM-8 6 Shaft Drum
- CPM-10 6 Shaft Drum
- CPM-10 8 Shaft Drum
- CPU-10FC 4 Shaft Drum
- CPU-10FC 6 Shaft Drum
- CPM-10 (6 Shaft) Shaft
- CPM-10 (8 Shaft) Shaft
- CPU10FC 11-3/8″ Shaft for use on 10″ Drum
- CPU12 13-5/8″ Shaft for use on 12″ Drum
- Bushing 3/4″ inside diameter
- Steel Spacer
- Spacer 1-1/2″ OD x 3/4″ ID
- For use with Edco Scarifier
.
7889 Edco Scarifier Start-UP Kits by
Drum Not Included With Startup Pack
| Edco | |
| CPM-8 Pak 1 | 215 Spacers, 6 Shafts |
| CPM-8 Pak 2 | 175 Spacers, 6 Shafts |
| CPM-8 Fine Setup | 174 Spacers, 6 Shafts |
| CPM-10 6 Shaft Pak | 252 Spacers, 6 Shafts |
| CPM-10 8 Shaft Pak | 384 Spacers, 8 Shafts |
| CPU10FC 6 Shaft Pak | 240 Spacers, 6 Shafts, 12 Bushings |
| CPU10FC 4 Shaft Pak | 130 Spacers, 4 Shafts, 8 Bushings |
| CPU-12 Pak | 300 Spacers, 6 Shafts, 12 Bushings |
.
7881 Edco Traffic Line Remover Cutter Assembly by
Edco TR-3 Cutter Assembly for Edco Traffic Line Remover
24 Bit Assembly
- Aggressive removal of thermoplastic lines
- Use on uneven, rough, chip-and-seal asphalt surfaces
48 Bit Assembly
- Minimum surface penetration
- Remove paint markings
- Remove tape lines
- Remove epoxy markings
- Ideal for use on asphalt
.
7882 Edco Scabblers by
Edco Scabblers
Scabblers use compressed air to hammer piston-mounted bits into the concrete surface roughening the concrete surface more than grinding or scarifying. EDCO’s Chip-Dek Scabbler can remove up to 1/4 inch of concrete surface in a single pass. The actual production rate depends on the strength of the concrete. A typical removal rate for a machine with a 12-inch working width is 200 to 250 square feet per hour at a 1/8-inch depth.
| Edco | ||
| Power | ||
| Air Power | at 100PSI |
at 100PSI |
| Phase | ||
| RPM’s | ||
| Belts | ||
| Length | ||
| Width | Weight |
Edco CD-3 3-Head Scabbler
Production Rate:
- Remove up to 200 sq ft per hour at depth per pass of 3/16″
- 3 Scabbler heads provide 8″ working width
Production Notes:
- Provides 1200 hits per minute for fast surface removal
- 2″ Vacuum Port for dust-free operation
- Equipped with an in-line lubricator
- Equipped with a Whip-check safety cable, assures safe air hose hookup
- Heavy-duty 1/4″ steel frame
Ideal For:
- Creating slip-resistant surfaces
- Creating wheelchair access ramps
- Creating excellent bonding texture for overlays
- Sidewalk trip hazard repair
- Removing delaminated concrete surface materials
- Removing spalled or deteriorated concrete
- Reducing high spots or leveling uneven joints
- Texturing parking garage ramps
Edco CD-5 5-Head Scabbler
Production Rate:
- 5 Scabbler heads provide 11-1/2″ working width
- Remove up to 250 sq ft per hour at depth per pass of 1/4″
Production Notes:
- Provides 1200 hits per minute for fast surface removal
- Equipped with a Whip-check safety cable, assures safe air hose hookup
- Requires only 160 CFM at 100 PSI
- Heavy-duty 1/4″ steel frame
- Wide T-Grip Handle and 8″ wheels for superior balance and handling
- 3″ Vacuum Port for dust-free operation
- Automatic in-line oiler
Ideal For:
- Creating slip resistant surfaces
- Scabbling down high spots or leveling uneven joints
- Roughening surfaces for new overlayments
- Creating wheelchair access ramps
- Creating excellent bonding texture for overlays
- Removing delaminated concrete surface materials
- Removing epoxy
- Texturing parking garage ramps
- Removing spalled or deteriorated concrete
- Breaking up ceramic tile
.