Best Door Tools Store

• Free Shipping from IMER factory warehouse
• 14″ Blade capacity, 1″ arbor.
• Motor 2850 Rpm, Blade 2150 Rpm.

MS 350SC

• 1.5 hp motor runs on 110 volts, 15 amps
• Head tilts to 45 degrees
• Optional 2.8 hp single phase 220 Volts motor (call for pricing)

MS 350F

• 1.5 hp motor runs on 110 volts, 15 amps
• Fixed Head
• Lighter than MS 350SC

MS 350G

• 5.5 hp Honda motor with oil bath clutch engine
• Gear box drive means less vibration and maintenance.

Features

• 16″ x 16″ Heavy Duty table, cuts 4 bricks at once
• Rigid single arm motor mount allows for cutting large pieces
• Built in stand with wheel kit
• Low voltage coils protect the vital components such as the on/off switch and motor from low or inadequate power sources.
• Hi-torque motors and serpentine drive belts ensure fast and smooth cutting performance
• Blade guards and panic stop buttons that keep safety inspectors happy
• The cutting tray rides on 1″ square steel bars that are fully adjustable, these saws remain accurate all the time!
• The cutting tray rollers keep the tray in place at all times the tray will not wheelie up n’ down as you pass a block through the blade
• A plunge stop is designed into the saw, the blade cannot cut into the cutting tray
• The box steel frames are light and very rigid, this allows for the single arm design, pass extra wide and extra long materials with no problem

.

MK-2000PRO Series Masonry Saw

• Free stand, rip guide, and 14″ BX-30 general purpose wet/dry diamond blade
• Call for special coupon savings on 2 hp electric and 5 hp gas saws
• Free shipping from MK warehouse, to lower 48 states; We will charge applicable sales tax, for a factory direct drop-ship In the state of California
• 5″ depth of cut
• Precision engineered, cast-aluminum structural components & jig-welded steel frame assembly
• Stay level blade guard gives 180 degree coverage at all times
• Drop down blade shaft is built with sealed, permanently lubricated, heavy-duty bearings
• Open-back design allows for material up to 16″ long to be cut
• Recoil spring return cutting head
• Cast aluminum blade guard with stainless steel water tubes that will not bend or rust
• Adjustable water supply for maximum blade protection
• Dimensions: Length 34″x Width 24.5″x High 41.5″.
• Blade rotation 3450 Rpm.
• One-year limited warranty

MK-2000 Pro Electric Saw Features

• Professionally engineered, thermally protected powerful “dual-voltage” AC induction motor
• Shaft system utilizes dual “V” belts and precision machined pulleys
• Convenient toggle switch to change motor from 115 Volts and 230 Volts
• Includes a powerful, fully submersible electric water pump

MK-2000 Pro Gas Saw Features

• Reliable and powerful 5 1/2 HP Honda or 6 HP Robin gas engine
• Shock-absorbing engine mounts for smooth operation
• Shaft system utilizes Micro “V” belts and precision machined pulleys
• Belt driven, self-priming centrifugal water pump on gas series saws

.

MK-5009T 9 hp Series Masonry Saw

• Includes 20″ blade guard. Call for pricing on 14″ & 24″ blade guards
• Block saw that will slice through an 8″ x 8″ x 16″ concrete block in a single pass.
• Precision screw feed mechanism allows the cutting head to be easily raised or lowered to the precise cutting depth required.
• The MK-5009 series is engineered with a host of innovative operator conveniences to boost efficiency, increase productivity, and enhance safety.

Model	MK-5009T 230V	MK-5009T 460V
Motor	3 Phase 60Hz	3 Phase 60Hz
Motor rpm	1725 rpm	1725 rpm
Shaft rpm (14″ Blade)	2700 rpm	2700 rpm
Shaft rpm (20″ Blade)	1925 rpm	1925 rpm
Shaft rpm (24″ Blade)	1540 rpm	1540 rpm
Max. Blade Capapcity	24″	24″
LxWxH (inches)	53″ x 25.5″ x 63″	53″ x 25.5″ x 63″

• Free shipping from MK factory warehouse to a commercial address in the lower 48 states
• The cutting head is controlled by a foot pedal so operator’s hands are free and safe
• Stay level blade guard with flange safety cover gives 180 degree coverage at all times as an extra safety protection factor
• 20″ blade capacity gives 8″ depth of cut
• 38-1/2″ table travel with 22″ cutting length
• Open-back design allows larger material to be easily rip cut
• Adjustable water supply for maximum blade protection
• One-year limited warranty
• Model MK-5009T: 240V/60Hz three phase 9 hp motor
• Model MK-5009T: 460V/60Hz three phase 9 hp motor
• 8% sales tax on orders shipped to residence of CA

.

MK-5005 Series 5 hp Masonry Saw

• Precision screw feed mechanism allows the cutting head to be easily raised or lowered to the precise cutting depth required
• Stay level blade guard cover gives 180º coverage at all times
• Open-back design allows for material up to 20″ long to be cut
• Conveyor cart built from heavy-duty cast aluminum
• 3 phase saws are equipped with GE NEMA 1 starters in NEMA 12 enclosure
• Adjustable water supply for maximum blade protection
• Built-in tie-downs for safer saw transport
• Ergonomically designed handle for reduced operator fatigue
• Spherical rod ends are used to maintain proper cutting head alignment
• Gas saw engine attachment is via four vibration isolation mounts
• Gas saws come with belt driven, self-priming centrifugal water pumps that can be disengaged for dry cutting
• Heavy-duty built-in forklift brackets allow lift to approach from the front or either side of the saw
• One-year limited warranty

Model	MK-5005S	MK-5005T	MK-5005T
Motor	230V 60Hz	230V 60Hz 3 Phase	460V 60Hz 3 Phase
Motor RPM	1,725	1,725	1,725
Shaft RPM (14″ Blade)	2,700	2,700	2,700
Shaft RPM (20″ Blade)	1,925	1,925	1,925
LxWxH (inches)	53″ x 26″ x 63″	53″ x 26″ x 63″	53″ x 26″ x 63″

.